Rover SD1 Exhaust Insulation Wrap
Exhaust Insulation Wrap
Thermo-Tec Insulating Wrap gives safety with performance.
Tubular manifolds by design produce a vast amount of heat in the engine compartment. This increases the possibility of electrical/ignition components not working effectively and promotes a higher risk of fire (if any combustible material comes in to contact with the manifold), not to mention the likelihood of severe burns when working on the engine!
By wrapping your tubular manifold with Thermo-Tec insulating wrap you can overcome all these risk factors. Thermo-Tec keeps the heat within the manifold so the exhaust gases have a much higher velocity. This induces negative pressure (scavenging) which increases air intake flow, resulting in better performance & economy. It also reduces under bonnet noise.
Technical Notes: Thermo-Tec heat wrap – which is race & rally proven – comes in rolls 2 inches wide x 50 feet long and moulds to the contours of the manifold. Being a silica based fabric (it does not contain asbestos or carcinogens), it is unaffected by oil or water, withstands temperatures up to 1000 degrees Celsius and reduces under bonnet temperatures by up to 70%.
Snap-Strap Retaining Kit: We strongly recommend that you use Snap-Straps to retain the insulation. These are stainless steel straps with a narrow profile (for tight spots) that ou cut to length and fasten with snap type heads. Alternatively you can skin your knuckles and use hose clips!
V8 Sports Exhaust System Stainless Steel
Our ever-popular sports exhaust system for the V8 (derived from a race specification) is suitable for both manual and automatic, right hand or left hand drive vehicles.
The 7-piece system features a pair of 4 into 1 tubular manifolds coupled to link pipes, which incorporate flange connectors to join the manifolds to a large bore Y-pipe. From here onwards, the system is of a single pipe design.
The reason for flange joints on the link pipes is simple: some of our customers ask for the option of retaining the original cast manifolds and downpipes instead of tubular manifolds (with the associated cost saving). Consequently, fitting flange joints and special link pipes means that we can offer a system that can be fitted with or without tubular manifolds. The system incorporates a pair of free0flowing silencer, tucked away in the axle well so as not to interfere with ground clearance on the Vitesse (we do not recommend fitting where the ride height is lower than Vitesse). Another feature is the tailpipe, which is a separate section of 3 inch polished stainless steel, with a gentle upward curve to follow the contour of the rear valance.
Rolling road tests show that gains in power and torque can be expected, depending on the age, condition and set-up of your engine – please see graphs.
The system is also suitable for large capacity engines. The sound is pure Rover V8 but comfortably refined inside the car at cruising speeds.
Enhancements for Sports Exhaust
Our Sports Exhaust System is designed to give an increase in power & torque on an otherwise unmodified vehicle. The way it achieves this is by helping the engine to ‘breathe out’ more efficiently. Naturally, it works just as well (or even better) on modified engines, since most modifications are designed to make the engine breath more efficiently.
Fitting K&N air filters at the same time as our Sports System will help the engine to ‘breathe in’ more efficiently – by removing the restrictive standard air filter – yielding even better results. (For K&N filters, see our Fuel Section)
To gain maximum benefit from our Sports System, particularly in large capacity V8s (3.9 or even 4.6 litre versions), fit our Big Valve Performance cylinder heads. These heads are ported and gas-flowed to help the engine achieve optimum efficiency. (For Performance cylinder heads, refer to our V8 Engine Section)
Finally, don’t forget your fuel system: all this extra efficiency will be lost if your carbs are worn out or your injection system is not up to scratch! The original carbs should be adequate for an otherwise unmodified 3.5 engine fitted with a sports System and K&N filters (provided they are correctly set up). For the same vehicle fitted with modified cylinder heads or a bigger engine, however, we would recommend fitting either a Holley or Weber 4 barrel carb (see our Fuel Section).
Similarly, standard Efi vehicles will need no modifications to the injection system when fitting a Sports System and K&N. If further modifications are being considered, such as a change of camshaft, Performance cylinder heads or a bigger engine, we strongly recommend a remapped ecu to provide the correct fueling. We can remap your existing ecu to suit your engine’s requirements exactly, giving crisper throttle response, more power and torque and b4etter fuel efficiency (see our Electrical Section).