Introduction Carburettors Two makes of carburettor are fitted to Range Rovers as standard equipment: the Zenith 'Stromberg CD175' - used exclusively from 1970 to 1986 - and the 'SU HIF', which was fitted for a short period (alongside the Stromberg) from 1986 until carbs were replaced by fuel injection. The most obvious visual difference between the two types of carb is the dashpot; Strombergs having a very stubby dashpot with the 'Zenith' name cast into it, while the SUs have a much taller dashpot without any markings. Electronic Fuel Injection Electronic fuel injection (Efi) replaced carbs for Vogue models in October 1985, and for all V8 4-dr models from November 1986, giving a substantial power increase without significant changes to the engine. There are two types of Efi system fitted to the Range Rover: The first system - Lucas L-Jetronic - uses an airflow meter, inside which is a hinged flap that measures, by deflection, the flow of air into the engine, thus varying the voltage signal to the ECU. The second system - introduced to coincide with the 'new' 3.9 litre engine in 1988 but also fitted to some 3.5 litre engines - incorporates a 'hotwire' air metering system, which contains no moving parts. Instead, it employs two sensor wires - one of which is heated - to measure air mass as it passes over the wires and into the engine. A voltage signal is then sent to the ECU proportionate to the voltage required to maintain the temperature of the heated wire as it is cooled by the air flow. The flap type, fitted to the first 3.5 Efi (non cat'-equipped) models from 1986, is similar (though not identical) to the system fitted to the Rover SD1 Vitesse from the same time. The hotwire type, fitted to later 3.5, 3.9 & 4.2 vehicles (with or without cat's), despite appearing quite similar, shares few parts with the flap type system. Diesel The first diesel-powered Range Rovers left the factory in April 1986, fitted with the Italian VM 2.4 litre turbocharged engine. Subsequently, the larger 2.5 litre VM unit, followed by Land Rover's own 200 & 300Tdi engines, were fitted. There have also been numerous diesel conversions carried out over the years, including some factory kits. However, the parts listed under Diesel Fuel System Components apply only to factory-built diesel vehicles. 4 Barrel Carbs Finally, we offer a choice of conversion kits for V8 Range Rovers (carb or efi, all engine sizes): Holley carb. Based on the legendary Holley carburettor. The kit includes a 390cfm 4 barrel Holley carb, with vacuum secondaries and electronic choke, an Offenhauser inlet manifold and choke cable kit and full instructions. Edelbrock Performer. A 500cfm 4 barrel carb kit, complete with all necessary components, which is designed to improve performance and economy. Performer carbs also feature a bright finish which enhances the appearance of your engine. Both carbs are ideal for on or off roaders and are suitable for any engine size.

Carb Identification

Stromberg CD175 Vehicles from 1970 to 1896 Non Detoxed Engines - Engine Number Tag Number 355 suffix C, D & E 3712 355 suffix F -   3550000F to 35542952F 3881 35542953F onwards 3915 13D & 18D 3915 Detoxed Engines - 341 & 359 -   Suffix A & B 3318 Suffix C & D 3677 Suffix E 3887 Suffix F 3854 34183127F 3999 398 3881 11D, 15D, 16D, 17D & 19D 4104 Vehicles from 1986 onwards Non Detoxed Engines - 28D & 29D 4185 Detoxed Engines - 26D & 27D 4187 30D 4186		SU HIF Vehicles from 1896 onwards Non Detoxed Engines - Engine Number Tag Number 28D & 29D FZX2006 Detoxed Engines - 26D, 27D & 30D FZX2005
		Carb Identification Both makes of carburettor have a silver tag - stamped with an identification number - which is attached to the carb by one of the dashpot retaining screws. (Note; both RH & LH carbs have the same number but with an R or L suffix as appropriate). However, if the tag is missing, the engine number will help you to identify the carburettors, providing they have not been replaced by a previous owner.
		Carburettor Care & Overhaul Fuel economy and performance can suffer with insufficient carb maintenance, and with the tightening of the MOT regulations regarding exhaust emissions it is more important than ever that the fuel system is maintained in good working order. Incorrectly adjusted or worn carbs can also cause overfuelling and 'bore-wash', resulting in excessive oil consumption. It is quite straightforward (with the help of a workshop manual) to service and overhaul your carbs, using the service items listed in this section. The listings for complete carburettors are for identification purposes only. They will also show if you have the correct type of carbs fitted. Part numbers, tag numbers & engine numbers are quoted to help identify the original factory specification. However, these numbers relate to carburettors fitted when the vehicle was new, and not to subsequent replacements.

Inlet Manifold Fittings - V8

Gasket (Inlet manifold);
All models.
Tin - (1) - ERC3990
Composite - (1) - ERR7306

End seal (Manifold gasket);
for tin gasket - (2) - AJM645
for composite gasket - (2) - ERR7283

Clamp (End seal) - (2) - 602076
Screw (Seal clamp) - (2) - 602236
Thermal transmitter - (1) - 545010
Located behind thermostat.
Gasket (Thermal transmitter) - (1) - 236022

Non-return valve (Brake servo);
Not ABS models.
Carb models - (1) - ADU1402
Efi models - (1) - RTC5907

Washer (Non-return valve) - (1) - 232043
Heater outlet (Rear) - (1) - 603440
Gasket (Rear heater outlet) - (1) - 603441

Temperature sender unit;
Located at front of inlet manifold.
Carb models -
Air con - (1) - PRC6317
Non air con - (1) - GTR108
Efi models -
3.5 litre
Air con - (1) - PRC6317
Non air con - (1) - GTR108
3.9 litre
Air con & non air con - (1) - PRC7918

Washer (Temperature sender unit) - (1) - 90568054

Thermostat;
All models.
74° - (1) - ETC4761
82° - (1) - 602687
88° - (1) - ETC4765

Thermostat housing;
Without electric fan switch -
Eng nos. 341, 355 ,359 only - (1) - RB7322
All other models - (1) - ERC2139
With integral electric fan switch -
Air con - (1) - ETC6135
Non air con - (1) - ETC4596

Gasket (Thermostat housing);
Eng nos. 341, 355, 359 - (1) - 610387
All other models - (1) - ERR2429

Fan switch (Thermostat housing) - (1) - PRC3505
Washer (Fan switch) - (1) - C457593A

Carburettor Components - Stromberg CD175 (1970 to Oct 1985)

---

Diaphragm - (2) - JS499A
All models.
Spring (Diaphragm) - (2) - 606792

Gasket kit;
Carbs 3712, 3915 - (2) - 605857
All other carbs - (2) - RTC1481A

Metering needle (Non detoxed vehicles);
Carb No. 3712 - (2) - 606793
Carb No. 3881 - (2) - AAU8231
Carb No. 3915 - (2) - AEU2462

Metering needle (Detoxed vehicles);
Carb No. 3318 - (2) - 90608276
Carb No. 3677 (BIDF) - (2) - AAU1488
Carb No. 3677 (BIFF) - (2) - RTC4776
Carb No. 3887 - (2) - AAU8229
Carb No. 3854 (BIEJ) - (2) - AAU8230
Carb No. 3854 (BIFF) - (2) - RTC4776
Carb No. (BIFC) - (2) - AEU1850
Carb No. 4104 - (2) - AEU1851

Needle valve;
Carb No. 3712 - (2) - AAU1484
Carb No. 3881 & 3915 - (2) - RTC1482
Carb No. 3318 - (2) - 606300
Carb No. 3677 - (2) - AAU1484
Carb No. 3887 & 3854 - (2) - RTC1482
Crab No. 3999 - (2) - BHM1079L
Carb No. 4104 - (2) - RTC1482

Float - (2) - 605833
All models.

Temperature compensator;
Carb No. 3318, 3677, 3887 & 3854 - (2) - 90608271
Carb No. 3999 & 4104 - (2) - AAU7900

Throttle disc;
Carb No. 3712, 3881 & 3915 - (2) - 605800
Carb No. 3318 - (2) - 597770
Carb No. 3677, 3887, 3854 & 3999 - (2) - AAU1489
Carb No. 4104 - (2) - AEU1848

Damper & oil cap - (2) - 518432A
All models.
Chrome dashpot cover - (2) - RS1514
Fit over your existing dashpots to enhance the appearance of your engine.

Cold start assembly;
Carb No. 3712 & 3915 - (1) - 606810
Carb No. 3318 & 3677 - (1) - 608282

Vacuum switch - (1) - 614361
Detoxed engines.
Fuel trap - (1) - ERC2042L
Detoxed engines.

Carburettor Components - Stromberg CD175 (1986 onwards)

---

Diaphragm - (2) - JS499A
Spring (Diaphragm) - (2) - 606792
Gasket kit - (2) - RTC1481
Service kit - (2) - AAU2967
Kit includes needle valve, diaphragm, float gasket and seals.

Metering needle;
Carb No. 4186 - (2) - AEU1851
carb No. 4187 (To VIN 162496) - (2) - AEU1851
Carb No. 4187 (VIN 162497 onwards) - (2) - RTC4774
Carb No. 4185 - (2) - AEU1850

Needle valve - (2) - RTC1482
Float - (2) - 605833
Temperature compensator - (2) - AAU7900
Throttle disc - (2) - AEU1848
Damper & oil cap - (2) - 518432A
Chrome dashpot cover - (2) - RS1514
Fit over your existing dashpots to enhance the appearance of your engine.
Fuel trap - (2) - ERC2042L

Carburettor Components - SU HIF (from 1986)

---

Engine numbers with a 'C' suffix.
Seal kit - (1) - RTC6072

Metering needle;
Carb No. FZX2005 - (2) - NZX8077L
Carb No. FZX2006 - (2) - NZX8076L

Jet assembly;
RH - (1) - CUD2785L
LH - (1) - CUD2788L

Needle guide - (2) - JZX1039
Float needle & seal kit - (2) - STC205

Float;
RH - (1) - LZX1600L
LH - (1) - RTC3566

Piston spring - (2) - AUD4398
Damper & oil cap - (1) - LZX1505
Fuel trap - (2) - ERC2042

Carb Mountings

---

Stromberg & SU carbs.

Gasket - (6) - ERR4381

Insulating block;
Carb No. 3712, 3881 & 3915 - (2) - ERC1102A
All other carbs - (2) - ERR4383

4 Barrel Carb Conversion Kits

---

Suitable for all engine sizes.
Complete conversion kits for all V8 Range Rovers.
Kits include 4 barrel carb, inlet manifold, chromed 14" air cleaner, thermostat housing and accelerator cable kit.

Holley conversion;
Kit 1 - (1) - RB7262
With 3" deep air cleaner.
Kit 2 - (1) - RB7262L
With 2" deep air cleaner for extra bonnet clearance.

Edelbrock Performer conversion;
Kit 1 - (1) - RA1323
With 3" deep air cleaner.
Kit 2 - (1) - RA1323L
With 2" deep air cleaner for extra bonnet clearance.

4 Barrel Carb Components

---

Carburettor only;
Weber 500 - (1) - RA1335
Holley 390 - (1) - RB7254

Jets (390 carb) - (1) - RB7254JET
Pair.
Overhaul kit (Holley 390) - (1) - RB7254OH
Holley Stud/Nut/Washer Set - (1) - RB7254S
Gasket (Carb to manifold) - (1) - RB7181
Holley & Weber.

Inlet manifold (4 barrel carb);
Suitable for Weber & Holley carbs.
Offenhauser 360° - (1) - RB7314
Dual plane. Lowest bonnet clearance.
Offenhauser/JWR (dual port) - (1) - RA1336
Edelbrock performer - (1) - RA1337
Dual plane. High torque.

Gasket (Inlet manifold);
Tin - (1) - ERC3990
Composite - (1) - ERR7306

End seal (Manifold gasket);
for tin gasket - (2) - AJM645
for composite gasket - (2) - ERR7283

Thermostat housing;
Cast iron - (1) - RB7322
Chromed - (1) - RB7437

Gasket (Thermostat housing) - (1) - GTG116
Accelerator cable kit - (1) - RB7278
Holley & Weber.
Manual choke conversion kit - (1) - RB7184
Holley.
Manual choke cable - (1) - RB7290
Holley.

Air cleaner;
14" diameter chromed 'pancake' type, complete with filter.
Standard 3" deep - (1) - RB7438
'Low-Rider' 2" deep - (1) - RB7439
For extra bonnet clearance.

Replacement element (Air cleaner);
3" deep - (1) - RB7438ELEM
2" deep - (1) - RB7439ELEM

Adaptor (Breather pipe) - (1) - RB7654
Air cleaner base to flame trap/breather.

K & N Air filter (4 barrel carbs);

K & N Holley & Weber 4 Barrel carbs;
Pancake (14") filter assembly, bolts directly on to carb.
May also be fitted with 'X-Stream' filter top (lid).
Recessed type (assembly) - (1) - RA1397
Sits low on carb for extra bonnet clearance.
N.B. for use with manual choke only.
Flat type (assembly) - (1) - RA1398
2¼" deep, fits either manual or automatic choke.
'X-Stream' air flow (lid only) -
Black - (1) - RA1399BLACK
Blue - (1) - RA1399BLUE
Red - (1) - RA1399RED
Polished - (1) - RA1399POLISHED
For maximum air flow. Replaces standard pancake K & N lid.
Available in black, blue, red or polished.
N.B. K & N filter assembly (recessed or flat type) must be purchased separately.

Inlet Manifold Fittings - Airflow Meter Efi (3.5 litre)

---

Fuel pressure regulator;
Standard - (1) - ERR268
Adjustable - (1) - EAC1284UR
Recommended for performance applications. Increases fuel pressure, according to inlet manifold demand, by a greater ratio than standard.

Uprated fuel pump resistor - (1) - DRC3017HP
Use in conjunction with adjustable pressure regulator. Enables fuel pump to cope with extra fuel demand.
Auxiliary air valve - (1) - ERC3617
Thermotime switch - (1) - EAC1385
Temperature sensor - (1) - ETC8496A
Sealing washer (Temperature sensor) - (1) - 243967
Injector - (8) - ERC3620A

'O' ring seal (Injector);
Large (Upper) - (8) - EAC2414A
Small (Lower) - (8) - EAC2415A
Fuel hose (8cm) - (2) - TKC6351
High pressure Efi hose to join fuel rails.
Fuel hose (Cold start injector) - (1) - ETC7241A
Also suitable for pressure regulator.
Clamp (Efi hoses) - (ar) - C435996L
Over-run fuel cut off switch - (1) - ETC6143

Inlet Manifold Fittings - Hotwire Efi (3.9 litre)

---

Fuel Pressure Regulator - (1) - ETC8494
Temperature sensor - (1) - ETC8496A
Sealing washer (Temperature sensor) - (1) - 243967A

Injector;
3.5 litre - (8) - ETC6264
3.9 & 4.2 litre - (8) - ERR722

'O' ring (Injector) - (16) - RTC5679
Clip (Injector) - (8) - ETC6375
Fuel temperature sensor - (1) - ETC6661
Front of fuel rail.

Plenum Chamber Components

---

Screw (Hex key type) - (6) - SS108801
Plenum chamber to ram housing.

Throttle disc;
Engine nos. 22D & 23D - (1) - ETC5772
Low compression.
All other engines - (1) - ETC6222A

Throttle spindle;
Engine nos. 22D & 23D - (1) - ETC5771
Low compression.
All other engines - (1) - ETC6223A

Bush (Throttle spindle) - (2) - 611795
Seal (Throttle spindle) - (2) - AUD3577

Idle speed screw;
To July 1987 - (1) - ERC7809
From July 1987 - (1) - ST606080

Throttle potentiometer;
3.5 litre - (1) - ETC5598
31D engine nos. only - (1) - ETC6443
3.5 litre hotwire type.
3.9 & 4.2 litre - (1) - ETC8495

Gasket (Potentiometer) - (1) - ERR4944
Cold start injector - (1) - EAC1383
Airflow meter type Efi only.
Idler control assembly - (1) - ETC6214
Stepper motor - (1) - ETC6660
Air-valve solenoid - (1) - ERC7536A
Air con models.
Breather hose - (1) - ERC9116A
Flame trap to plenum.
Hose (Extra air valve to plenum) - (1) - ERC9117
'C' - shaped hose.
Non return valve (Servo) - (1) - RTC5907
Pneumatic actuator - (1) - ETC7150
Cruise control.

Electronic Components - Efi

---

New ECU - For availability and price of New ECUs, please contact our sales department.
Reconditioned ECU - We can recondition your existing Lucas 4CU (flap-type) or 14 CUX (hotwire type) ECU to original specification, or recalibrate both types for power and economy, on standard or modified engines.
All ECUs are guaranteed for 1 year.
Please contact our sales department to discuss your requirements.

Diode pack (relay) - (1) - DAC1861
Red.

Relay (Fuel pump);
Non catalyst vehicles - (1) - AGU1068
Catalyst vehicles - (1) - AFU2913L

Tune resistor;
Red - (1) - PRC8005
Yellow - (1) - PRC8007
White - (1) - PRC8009
Green - (1) - PRC8172
Blue - (1) - AMR2016

Airflow meter;
Flap type - (1) - ERC9127A
Hotwire type - (1) - ESR1057

Air intake hose;
Air cleaner to airflow meter - (1) - NRC9996
Flap type only.
Airflow meter to plenum chamber -
Flap type - (1) - NRC9997
Hotwire type
To 1994 (VIN LA) - (1) - ESR1611L
1995 (VIN MA onwards) - (1) - ESR1807

Hose clip;
Air cleaner to airflow meter - (2) - RTC3518
Flap type.
Airflow meter to chamber - (2) - CN100908
All models.

Power resistor - (1) - DAC1211A

Fuel System Components - Diesel

---

Glow plug;
2400/2500TD - (4) - ADU9955
200/300Tdi - (4) - ETC8847

Injector pump assembly;
2400TD - (1) - RTC4919
2500TD - (1) - RTC6659
200Tdi - (1) - ERR459
300tdi - (1) - ERR4419

Gasket (Injector pump);
2400/2500TD - (1) - STC807

Solenoid (Fuel shut-off);
2400TD - (1) - AEU3031
2500TD - (1) - RTC6702

Switch (Cut-off);
200/300Tdi - (1) - RTC6702

Injector assembly;
2400/2500TD - (4) - AEU2098E
200Tdi - (4) - ETC8412
300Tdi - (4) - ERR3339

Accelerator & Choke Control

---

Accelerator cable - V8 Carb;
RHD
4 speed manual - (1) - 566426
5 speed manual - (1) - NRC8388
Automatic - (1) - NTC3083
Australia only - (1) - NRC2191
LHD
Manual - (1) - 577356
Automatic - (1) - NTC3084

Accelerator cable - V8 EFi;
Up to VIN FA (1989)
RHD
3.5 & 3.9 - (1) - NTC1054
LHD
3.5 - (1) - NTC4842
3.9 - (1) - NTC6723
From VIN GA (1990) onwards
RHD
3.9 & 4.2 - (1) - ANR5328
LHD
3.5 - (1) - NTC7198
3.9 & 4.2 - (1) - ANR5327

Accelerator cable - 2400/2500TD;
Up to VIN FA (1989)
RHD - (1) - NTC1461
LHD - (1) - NTC1460
VIN GA (1990) onwards
RHD - (1) - NTC7830
LHD - (1) - NTC7189

Accelerator cable - 200 TDi;
RHD
To VIN KA628559 (1993) - (1) - ANR1860
VIN KA628560 onwards - (1) - ANR3592
LHD
All models - (1) - ANR3606

Choke cable - V8;
Stromberg carbs
RHD - (1) - NRC9094
LHD - (1) - NRC9095
SU Carbs
RHD & LHD - (1) - NTC3690

Air Filter

---

Air filter;
Carburettor -
All except Australia - (2) - 605191
Australia only - (2) - GFE1124
Seal (Air filter) - (4) - RTC5888
Except Australia.
Efi -
To 1994 (VIN LA) - (1) - RTC4683
1995 (VIN MA) onwards) - (1) - ESR1445
Diesel -
2400/2500TD - (1) - NTC1435
200Tdi - (1) - ESR1049
300Tdi - (1) - ESR1445

K & N Air filter;
K & N offer superior filtration, an improvement in air flow and many times longer life than standard elements. In addition, they can be cleaned and re-used.
Available for both Carburettor and Efi petrol models, as well as diesel-engine Range Rovers, they replace the original air intake box and paper element and require no alterations to the fuel system on a standard engine (with standard exhaust). K & N Filters are proven in both competition and off-road environments.
NOTE: For 4 barrel carb filters see 4 Barrel Carb Components

K & N Filter;
Carb vehicles -
Stromberg & SU - (2) - RB7296
Efi vehicles -
Flap type - (1) - RA1063
Hotwire - (1) - RA1060
Diesel vehicles -
2400/2500TD - (1) - NTC1435K-N
200Tdi - (1) - ESR1049K-N
300Tdi - (1) - ESR1445K-N

Cleaning fluid (1 litre) - (ar) - RX1346
for cleaning filter element.

Element oil;
For re-oiling element.
1 fl oz sachet - (ar) - RX1347
250ml bottle - (ar) - RX1348
400ml aerosol - (ar) - RX1349

Engine Breather System

---

Breather/flame trap;
Right hand rocker cover (where fitted).
Original - (1) - RB7432
Short type - EFi original size - (1) - RB7432LOW
Powder coated -
Black - (1) - RB7432PC BLACK
Red - (1) - RB7432PC RED
Chromed - (1) - RB7432C

Breather grommet (pair) - (1) - RB7432ZGROMMET
'O' ring seal (Flame trap) - (1) - 564258

Breather filter;
All except Australia - (1) - GFE7004
Located on rear of cylinder block.
Australia only - (1) - GFE7004
Located on left hand rocker cover.

Engine breather - (1) - ERR1471
200/300Tdi.

Hose (Breather);
Diesel.
2400/2500TD - (1) - BAU5090L
200Tdi - (1) - ERR3381
300Tdi - (1) - ERR4689

Fuel Pump

---

Fuel Pumps Early, non power steering, V8 range Rovers have a mechanical fuel pump bolted to the timing cover and driven by a lobe on the camshaft spacer. Power steering equipped cars have an electric fuel pump (due to the location of the p.a.s. pump where the fuel pump had previously been), either horizontally mounted - up to vehicle suffix B - or vertically mounted - suffix C onwards. From 1986, the fuel pump for both carb and Efi vehicles is fitted inside the fuel tank. However, the two are not interchangeable, as the Efi pump is a high pressure type not suitable for carb vehicles. Up to approximately 1991, the in-tank fuel pump is separate from the fuel level sender. From 1991 onwards, the pump and sender unit are combined. Diesel vehicles are equipped with an engine-driven, mechanical fuel pump.

Carb - 1970 to 1986

Fuel pump;
Located in engine bay.
Mechanical - (1) - RTC6724
Electrical - (1) - PRC3901
Horizontal or vertical.

Pipe unions for PRC3901 - (2) - 572535
Gasket (Mechanical pump) - (1) - 602180A
Pump to timing cover.
Gasket (Electric pump) - (1) - 90606261
For PRC3901.
Mounting bobbin (Fuel pump) - (2) - NRC7135
For PRC3901.
Nut (Mounting bobbin) - (4) - GHF200
Earthing braid - (1) - 568244
Filter (Electric pump) - (1) - 90606262
For PRC3901.

Carb - 1986 on

Fuel pump - (1) - PRC7020
In tank type.
Gasket (Fuel pump) - (1) - ESR3278
Pump to tank.
Fuel pump (Uprated) - (1) - RB7259
Facet competition high capacity electric pump. Complete with unions.

Efi - 1986 on

Fuel pump;
To VIN HA464553 (1991) - (1) - PRC8318
Separate sender type.
VIN HA464554 to KA642682 - (1) - PRC9409
Combined pump/sender type.
VIN KA642683 (1983) onwards - (1) - ESR3926
Combined pump/sender type.

Gasket (Fuel pump);
Separate pump/sender - (1) - ESR3278
Combined pump/sender - (1) - NTC5859

Locking ring (Pump/sender) - (1) - NTC5858
Suppressor (fuel pump) - (1) - PRC7491

Diesel

Fuel pump;
2400/2500TD - (1) - AEU2291
200Tdi - (1) - STC1190
300Tdi - (1) - ERR5057

'O' ring (Pump to block) - (1) - AEU2152
2400/2500TD.
Gasket (Pump to block) - (1) - ERR2028
200/300Tdi.
Diaphragm (Pump) - (1) - AEU2151
2400/2500TD.

Fuel Filter

---

Carb Vehicles

Fuel filter assembly;
To approx' 1986 - (1) - 90577508
Approx' 1986 onwards - (1) - NRC9786

Element & seal (Filter) - (1) - JS660L
All models.

Seal (Bowl retaining bolt);
Outer - (1) - 606207
Inner - (1) - AEU1147

Efi Vehicles

Fuel filter;
To 1990 (VIN GA) - (1) - GFE7001
Push-on connector type.
1991 (VIN HA) onwards - (1) - ESR4065
Screw-on connector type.

'O' ring (Pipe to filter) - (2) - ESR259
Models from 1992 onwards.

Diesel Vehicles

Fuel filter element & seal;
Non heated - (1) - AEU2147
Heated - (1) - RTC5938

Switch (Heater) - (1) - STC612

Fuel Tank

---

Petrol

Fuel tank;
1970 - 1986 - (1) - 575601
Carb.
1986 up to 1990 (VIN GA) -
Separate in-tank fuel pump & sender.
Single vent breather - (1) - NTC2017
Multi vent breather - (1) - NTC4553
Jan 1991 to 1993 -
VIN HA464554 to KA638156 - (1) - NTC6741
Moulded plastic tank with combined pump & sender.
1993 onwards -
VIN KA638157 onwards - (1) - ESR2585

Diesel

Fuel tank;
To VIN GA464553 (1990) - (1) - NTC2017
VIN HA464554 to KA638350 - (1) - ESR460
1990 to 1993.
VIN KA638351 (1993) onwards - (1) - ESR2584

Fuel Level Sender Unit

---

Vehicles with separate fuel pump & sender.
See Fuel Pump for combined sender/pump.

Petrol

Sender unit;
1970 to 1986 - (1) - PRC4510
1986 onwards - (1) - PRC8822
With separate sender.

Seal (Sender unit) - (1) - ARA1502
Locking ring - (1) - ARA1501

Diesel

Sender unit;
Side mounted - (1) - PRC8823
Top of tank -
To VIN KA642683 (1993) - (1) - PRC7129</