|
|
|
Triumph 2000/2500 Engine Components |
|
Page Contents
Spin-On Filter Conversion Oil Feed Kit Oil Pressure Gauge Kit & Switch
Piston Sets Piston Ring Sets Oil Feed Kit Rocker Gear Overhaul Kit Rocker Shaft & Fittings, Pushrods & Followers
©Rimmer Bros Ltd - Registered in England No. 2155394. VAT No. GB 352 8473 40.
Cylinder Block Components
Sump Pan & Oil Pump
Oil Filter
Oil Pressure Gauge Kit & Switch
Oil Cooler Kit (engine)
Crankshaft & Flywheel
Piston & Ring Sets
Conrod & Bearings
Engine Gaskets & Oil Seals
Cylinder Head & Fittings
Rocker Shaft & Fittings, Pushrods & Followers
Valves, Guides & Springs
Rocker Cover & Fittings
Timing Gear
Camshaft
Front Engine Plate;
Manual Steering - (1) - 215373
Power Steering - (1) - 216995
Gasket (engine plate to block) - (1) - 215350
Rear Engine Plate;
Manual Gearbox - (1) - 211505
Auto Gearbox - (1) - 211677
Cylinder Liner - (6) - 158942
Stud - Cylinder Head - (14) - 156274
Nut - Cylinder Head - (14) - 103810
Washer - (14) - WB600070
For 103810 nut.
Core Plug Set - (1) - RG1034
For block & cylinder head.
Bolt - Main Bearing Cap - (8) - BH607241
Washer - Locking - (8) - WL600071
For bolt BH607241.
Front Sealing Block - (1) - 151134
Filler - (2) - 36234
Sealing block to cylinder block.
Screw - (2) - SW605081
Sealing block to cylinder block.
Gasket - (1) - UKC8321
Sealing block to cylinder block.
Oil Pressure Switch - (1) - GPS117
Oil Pressure Relief Valve - (1) - 132107
Spring - Oil Relief Valve;
Standard - (1) - 131535
Uprated - (1) - 131535UR
Washer - Oil Relief Valve - (1) - 6K433
Housing - Oil Relief Valve - (1) - 107246
Pedestal Distributor;
2000 Mk2 & 200TC - (1) - 126784
2.5Pi Mk2 (reconditioned) - (1) - 308396R
2500S & 2500TC - (1) - 126784
Gasket - Pedestal (.006") - (1) - 104939
All.
Stud * - (2) - TE605105
Pedestal to block.
Nut * - (2) - GHF201
For TE605105 stud.
Washer * - (2) - GHF332
For TE605105 stud.
* NOT required for 2.5Pi models.
Drive Shaft & Gear Assembly;
2000 Mk2/2000TC/2500S & 2500TC - (1) - 126786
Oil pump/distributor.
2.5Pi Mk2 - (1) - 149099
Distributor/metering unit.
Bush - Distributor Drive - (1) - 149776
Setscrew * - (2) - SH605071
Distributor to pedestal.
Washer - locking - (2) - GHF331
For HU807.
Washer - plain * - (2) - GHF300
For HU807.
NOT required for 2.5Pi models.
Engine Lifting Eye;
Front - (1) - 123716
Rear - (1) - 123715
Drain Plug (cylinder block) - (1) - 129077
Washer - fibre - (ar) - WF511A
For drain plug.
Stud (fuel pump to block) - (2) - TE605105
Crankshaft Oil Seals;
Front (timing cover) - (1) - UKC1110
Rear (main) - (1) - 143456
Housing - Rear Crankshaft Oil Seal - (1) - 156530
Gasket - (1) - 105321
For 156530 housing.
Oil Pump Assembly - (1) - 217488
Oil Pump Repair Kit - (1) - 217488REPKIT
Oil Pump Body only - (1) - 217486
Oil Screen/Strainer - (1) - TKC2006
Bolt (oil pump to block) - (3) - BH604281
Washer - Locking - (3) - GHF331
For BH604281.
Sump Gasket Set;
With Oil Seals - (1) - GEG214K
Less Oil Seals - (1) - GEG214
Sump Gasket only - (1) - GEG515
Drain Plug (sump) - (1) - 22G2115
Sump Pan - (1) - 308570
Setscrew (sump to block) - (23) - SH605051
Washer - Locking - (23) - GHF332
For SH605051.
Dipstick - (1) - 147712
Felt Washer - Dipstick - (1) - 32307
Dipstick Tube - (1) - 127652
Oil Pressure Switch - (1) - GPS117
Oil Filter;
Standard (canister element) - (1) - GFE131
Cartridge (for spin-on conversion) - (1) - RR1243
Canister Type Filter & Bowl - (1) - 510107
Washer/Seal (bowl) - (1) - 510109
This adaptor converts the standard 'Bowl' type Filter to the more efficient 'Spin-on' Cartridge type.
It makes filter changing easier (and cleaner).
Adaptor only (spin-on filter);
With Oil Cooler Fitted - (1) - RR1275
Without Oil Cooler Fitted - (1) - RR1238
Oil Filter (cartridge only) - (1) - RR1243
Rocker Gear Oil Feed Kit - (1) - RR1340
Remote mounted.
Oil Pressure Gauge Kit - (1) - RX1351OIL
Includes gauge, pipe etc.
Bracket - (1) - RB7050
For remote mounting of gauge.
Adaptor (oil pipe to block) - (1) - 143943
Adaptor (temp sender to water pump housing) - (1) - 11K2846
Washer (copper) - (1) - AED172
For adaptor 11K2846.
'T' Piece - (1) - RX1352
Use if retaining oil pressure switch.
Oil Pressure Switch - (1) - GPS117
Oil Pressure Relief Valve - (1) - 132107
Spring - Oil Pressure Relief Valve;
Standard - (1) - 131535
Uprated - (1) - 131535UR
Washer - Oil Relief Valve - (1) - 6K433
Housing - Oil Relief Valve - (1) - 107246
Oil Cooler Kit - (1) - RR1296
Includes oil cooler radiator, fitting kit, hose & fittings.
Also converts oil filter to spin-on cartridge type.
Thermostat- Oil Cooler - (1) - RS1456
Not supplied with oil cooler kit.
Oil Filter (cartridge only) - (1) - RR1243
Crankshaft;
2000 Mk2/2000 (1974) & 2000TC -
New (inc shells) - (1) - 308034K
New (less shells) - (1) - 308034
Reconditioned (inc shells) - (1) - 308034R
2.5Pi Mk2/2500 & 2500TC -
New (inc shells) - (1) - 311322K
New (less shells) - (1) - 311322
Reconditioned (inc shells) - (1) - 311322R
Thrust Washers;
Standard Size (pair) - (1) - BHM1366
+0.005" Oversize (pair) - (1) - BHM1366-005
+0.015" Oversize (pair) - (1) - BHM1366-015
+0.030" Oversize (pair) - (1) - BHM1366-030
Pilot Bush - Manual - (1) - 151213
All models.
Pilot Bush - Automatic;
2000 Mk2 (to ME50000) - (1) - 151823
2000 Mk2 (from ME50001) - (1) - 151396
2.5Pi Mk2/2000TC/2500S & TC - (1) - 151396
Main Bearing Set;
Standard Size - (1) - RTC1752
+0.010" Oversize - (1) - RTC1752-010
+0.020" Oversize - (1) - RTC1752-020
+0.030" Oversize - (1) - RTC1752-030
+0.040" Oversize - (1) - RTC1752-040
+0.060" Oversize - (1) - RTC1752-060
Big End Bearing Set;
Standard Size - (1) - RTC1751
+0.010" Oversize - (1) - RTC1751-010
+0.020" Oversize - (1) - RTC1751-020
+0.030" Oversize - (1) - RTC1751-030
+0.040" Oversize - (1) - RTC1751-040
+0.060" Oversize - (1) - RTC1751-060
Crankshaft Oil Seals;
Front (timing cover) - (1) - UKC1110
Rear (main) - (1) - 143456
Crankshaft Pulley (main);
Manual Steering (non viscous fan) -
2000 Mk2 - (1) - 154380
2.5Pi Mk2 * - (1) - 214479
Power Steering (non viscous fan) -
2000 Mk2 & 2.5Pi Mk2 * - (1) - 150215
Manual & Power Steering -
Vehicles fitted with viscous fan.
2000TC/2500S & TC - (1) - 154380
* Special Note-Pulleys: Pulley 214479 is no longer available.
Use 154380 as an alternative. Pulley 150215 is no longer available,
but we can quote to convert crank pulley/fan to later specification. Please enquire.
Woodruff Key - (1) - 133234
Oil Thrower (between sprocket & pulley) - (1) - 119390
Crankshaft Pulley (extension);
Manual Steering -
2000/2500S & 2500TC - (1) - UKC822
Power Steering -
2000/2500S & 2500TC - (1) - TKC1788
Sprocket - Crankshaft;
Single Chain (simplex) - (1) - 119389
2.0 litre engines.
Double Chain (duplex) - (1) - 145864
2.5 litre engines.
Shim - Crankshaft Sprocket;
Use as required.
0.004" - (ar) - 145275
0.006" - (ar) - 145276
Spacing Sleeve (sprocket to pulley) - (1) - 133235
Housing - Rear Crankshaft Oil Seal - (1) - 156530
Gasket - (1) - 105321
For 156530 housing.
Flywheel Assembly (manual) - (1) - 151214R
Reconditioned.
Ring Gear (manual/auto) - (1) - 201350
Bolt - Flywheel - (4) - UKC4254
Dowel - Flywheel - (1) - DP619
Driveplate - Flywheel (auto) - (1) - TKC5580
Fan Belt;
2000 Mk1 (to MB77659) - (1) - GCB11038
2000 Mk1 (from MB77660) - (1) - GCB11025
2000 Mk2/2000 (1974) & TC - (1) - GCB11088
2.5Pi Mk1 & Mk2 - (1) - GCB11088
2500 & 2500TC - (1) - GCB11088
Power Steering Belt - (1) - GCB10900
All models.
Piston Set;
Includes 6 pistons complete with rings and gudgeon pins.
2000 Mk2 (to ME50000) Flat Top Pistons -
Standard Size - (1) - 149976COUNTY
+0.020 Oversize - (1) - 149976-020COUNTY
+0.030 Oversize - (1) - 149976-030COUNTY
+0.040 Oversize - (1) - 149976-040COUNTY
2000 Mk2 (from ME50001) Domed Top Pistons -
Standard Size - (1) - 158112
+0.020 Oversize - (1) - 158112-020
+0.030 Oversize - (1) - 158112-030
+0.040 Oversize - (1) - 158112-040
+0.060 Oversize - (1) - 158112-060
2.5Pi Mk2 -
Standard Size - (1) - 148118
+0.020 Oversize - (1) - 148118-020
+0.030 Oversize - (1) - 148118-030
+0.040 Oversize - (1) - 148118-040
+0.060 Oversize - (1) - 148118-060
2000TC -
Standard Size - (1) - 158112
+0.020 Oversize - (1) - 158112-020
+0.030 Oversize - (1) - 158112-030
+0.040 Oversize - (1) - 158112-040
+0.060 Oversize - (1) - 158112-060
2500S & 2500TC -
Standard Size - (1) - 148118
+0.020 Oversize - (1) - 148118-020
+0.030 Oversize - (1) - 148118-030
+0.040 Oversize - (1) - 148118-040
+0.060 Oversize - (1) - 148118-060
Gudgeon Pin;
2000 - (6) - 127265
2500 - (6) - 149215
Circlip (gudgeon pin) - (12) - 508978
Piston Ring Set;
Includes rings for 6 pistons.
2000 Mk2 (to ME50000) -
Standard Size - (1) - 127262COUNTY
+0.020 Oversize - (1) - 127262-020COUNTY
+0.030 Oversize - (1) - 127262-030COUNTY
+0.040 Oversize - (1) - 127262-040COUNTY
+0.060 Oversize - (1) - 127262-060COUNTY
2000 Mk2 (from ME50001) -
Standard Size - (1) - RTC2428
+0.020 Oversize - (1) - RTC2428-020
+0.030 Oversize - (1) - RTC2428-030
+0.040 Oversize - (1) - RTC2428-040
+0.060 Oversize - (1) - RTC2428-060
2.5Pi Mk2 -
Standard Size - (1) - RTC2430
+0.020 Oversize - (1) - RTC2430-020
+0.030 Oversize - (1) - RTC2430-030
+0.040 Oversize - (1) - RTC2430-040
+0.060 Oversize - (1) - RTC2430-060
2000TC -
Standard Size - (1) - RTC2428
+0.020 Oversize - (1) - RTC2428-020
+0.030 Oversize - (1) - RTC2428-030
+0.040 Oversize - (1) - RTC2428-040
+0.060 Oversize - (1) - RTC2428-060
2500S & 2500TC -
Standard Size - (1) - RTC2430
+0.020 Oversize - (1) - RTC2430-020
+0.030 Oversize - (1) - RTC2430-030
+0.040 Oversize - (1) - RTC2430-040
+0.060 Oversize - (1) - RTC2430-060
Conrod Assembly - (6) - 146454R
Reconditioned.
Gudgeon Pin - piston;
2000 - (6) - 127265
2500 - (6) - 149215
Circlip (gudgeon pin) - (12) - 508978
Small End Bush - (6) - 119813
Dowel (hollow) - (12) - 107401
Bolt (conrod) - (12) - UKC2598
Bearing Set (big ends);
Standard Size - (1) - RTC1751
+0.010 Oversize - (1) - RTC1751-010
+0.020 Oversize - (1) - RTC1751-020
+0.030 Oversize - (1) - RTC1751-030
+0.040 Oversize - (1) - RTC1751-040
+0.060 Oversize - (1) - RTC1751-060
Head Gasket Set;
2000 Mk1 - (1) - GEG115
2000 Mk2 (to ME50000) - (1) - GEG179
Non recessed cylinder bores.
2000 Mk2 (from ME50001) - (1) - AJM1193
Recessed cylinder bores with tag gasket.
2.5Pi Mk1 - (1) - GEG179
2.5Pi Mk2 (to MG50000) - (1) - GEG179
Non recessed cylinder bores.
2.5Pi Mk2 (from MG50001) - (1) - AJM1193
Recessed cylinder bores with tag gasket.
2000 (1974) & 2000TC - (1) - AJM1193
2500S & 2500TC - (1) - AJM1193
Head Gasket only;
2000 Mk1 - (1) - 207102
2000 Mk2 (to ME50000) - (1) - GEG346
Non recessed cylinder bores.
2000 Mk2 (from ME50001) - (1) - GEG387
Recessed cylinder bores with tag gasket.
2.5Pi Mk1 - (1) - GEG346
2.5Pi Mk2 (to MG50000) - (1) - GEG346
Non recessed cylinder bores.
2.5Pi Mk2 (from MG50001) - (1) - GEG387
Recessed cylinder bores with tag gasket.
2000 (1974) & 2000TC - (1) - GEG387
2500S & 2500TC - (1) - GEG387
Rocker Cover Gasket - (1) - GEG413
Exhaust/Inlet Manifold Gasket;
2000 Mk1 only - (1) - AJM613
All other models - (1) - GEG682
Exhaust Downpipe Gasket;
2000 Mk1 only - (1) - GEG701
All other models - (1) - GEG718
Sump Gasket Set;
With Oil Seals - (1) - GEG214K
Less Oil Seals - (1) - GEG214
Sump Gasket only - (1) - GEG515
Timing Cover Gasket - (1) - 211126
Front Engine Plate to Block Gasket - (1) - 215350
Thermostat Gasket - (1) - GTG103
Water Pump Gasket;
Pump to Housing - (1) - 138701
Housing to Head - (1) - 138792
Fuel Pump Gasket - (1) - 138791
Oil Seal - Crankshaft;
Front (timing cover) - (1) - UKC1110
Rear (main) - (1) - 143456
Core Plug Set - (1) - RG1034
For block & cylinder head.
NOTE: Unleaded Fuel:Unless you are using an additive, then to convert your vehicle to run on unleaded fuel you will need to fit a reconditioned head with special valve seats and guides. These units are listed below. 2.5Pi owners will also need to fit a replacement metering unit and Bosch fuel pump (see 'Fuel' section for details).
Cylinder Head Assembly;
Reconditioned (unleaded).
Complete with valves & springs, less rockers & pedestals.
2000 Mk1 & 2000TC - (1) - RG1022R
2.5Pi Mk2 (to MG82076) - (1) - 516798R
2.5Pi Mk2 (from MG82077) - (1) - UKC1420R
2500S & 2500TC - (1) - RM8050R
Stud - Cylinder Head to Block - (14) - 156274
Nut - Cylinder Head Stud - (14) - 103810
Washer - Head Stud - (14) - WB600070
Rocker Gear Oil Feed Kit - (1) - RR1340
Remote mounted.
If your rocker gear is worn and noisy, this kit allows a significant saving to buying all the parts individually.
It includes new rocker shaft, 12 rocker arms, shaft springs and end plugs.
Rocker Gear Overhaul Kit - (1) - RR1312
Rocker Shaft Only - (1) - 214559
Rocker Shaft Complete (recon) - (1) - 214559RASSY
Rocker Arm;
Inlet (nos 1, 3, 5, 7, 9, 11) - (6) - 109023
Exhaust (nos 2, 4, 6, 8, 10, 12) - (6) - 109024
Screw - Tappet Adjusting - (12) - 109495
Nut - Locking - (12) - 57110
For 57109 screw.
Rocker Shaft Pedestal;
Number 1 (front) - (1) - 145867
Numbers 2, 3, 4, & 5 - (4) - 144974
Number 6 (rear) - (1) - 145869
Stud (rocker pedestal to head) - (6) - 132495
Nut (for 132495 stud) - (6) - GHF202
Washer - Plain - (6) - GHF333
For GHF202 nut.
Washer - Locking - (6) - WP184
For GHF202 nut.
Screw - Pedestal Locating - (1) - 104859
Setscrew - Oil Feed - (1) - SH605041
Washer - Copper - (1) - 500469
For SH605041.
Rocker Shaft Springs - (5) - 119313
Locates between rocker arms.
Plug - Rocker Shaft End - (2) - 137811
Spring - (2) - 105322
For 137811 springs.
Split Pin - (1) - PC10
For 137811 springs.
Push Rod;
2000 Mk2 (to ME50000) - (12) - 151073
2000 Mk2 (from ME50001) - (12) - 149513
2.5Pi Mk2 & 2000TC - (12) - 149513
2500S & 2500TC - (12) - 148916
Cam Follower (tappet) - (12) - 143552
Exhaust Valve;
2000 Mk2 (to ME75000) - (6) - 146084
2000 Mk2 (from ME75001) - (6) - 159872
2.5Pi Mk2 (to MG82076) - (6) - 149658
2.5Pi Mk2 (from MG82077) - (6) - 159873
2000TC/2500S & 2000TC - (6) - 159872
Inlet Valve (all) - (6) - 146128
valve Guide;
Inlet -
Standard - (6) - 58923
Bronze Type - (6) - 58923UR
Exhaust -
Standard - (6) - 111869
Bronze Type - (6) - 111869UR
Valve Spring (single type);
2000 Mk2 & 2000TC -
Standard - (12) - 136487
Heavy Duty (alternative) - (12) - 157229
2500S & 2500TC - (12) - 157229
Valve Spring (double type);
2.5Pi Mk2 -
Inner (to MG50000) - (6) - 102564
Inner (from MG50001) - (6) - 157476
Outer (to MG50000) - (6) - 149633
Outer (from MG50001) - (6) - 157229
2500S & 2500TC -
Inner - (6) - 157476
Outer - (6) - 157229
Split Collets (pairs) - (12) - 106663
Collar - Valve Spring (inlet);
Upper - (6) - 111870
Lower - (6) - 105118
Collar - Valve Spring (exhaust);
Upper - Outer - (6) - 128334
Upper - Inner - (6) - 128335
Lower - (6) - 105118
Alloy Rocker Cover;
Includes caps & nuts.
Alloy Finish - (1) - TKC378A
Black Crackle Finish - (1) - TKC378AP
Rocker Cover Gasket - (1) - GEG413
Oil Filler Cap;
For Standard Cover - (1) - GZC1400
For Alloy Cover - (1) - 214814C
Fixings - Standard Rocker Cover;
Stud - (2) - 105123
Locknut (lower) - (2) - GHF201
Bolt - (1) - BH605321
Nut (outer) - (2) - GHF272
Washer - (3) - GHF301
Fibre Washer - (3) - WF508
Timing Chain;
Single Chain (simplex) -
2000 Mk2 & 2000TC - (1) - 105131
Double Chain (duplex) -
2.5Pi Mk2/2500S & 2500TC - (1) - 145870
Sprocket - Camshaft;
Single Chain (simplex) - (1) - 35960
Double Chain (duplex) - (1) - 145865
Locking Plate (camshaft sprocket) - (1) - 36411
Setscrew - (1) - 100500
For 36411 locking plate.
Sprocket - Crankshaft;
Single Chain (simplex) - (1) - 119389
Double Chain (duplex) - (1) - 145864
Shim - Crankshaft Sprocket;
Use as required.
0.004" - (1) - 145275
0.006" - (1) - 145276
Tensioner - Timing Chain;
Single Chain (simplex) - (1) - 42425
Double Chain (duplex) - (1) - 145866
Anchor Plate - Tensioner (all) - (1) - 43752
Rivet - (1) - RR610040
For 43752 anchor plate.
Pin - (1) - 33214
For 43752 anchor plate.
Split Pin - (1) - PS103121
For 33214 pin.
Pedestal (distributor);
2000 Mk2 & 2000TC - (1) - 126784
2.5Pi Mk2 (reconditioned) - (1) - 308396R
2000S & 2500TC - (1) - 126784
Gasket - Pedestal (all) - (1) - 104939
0.006".
Stud * - (2) - TE605105
Pedestal to block.
Nut * - (2) - GHF201
For TE605105 stud.
Washer * - (2) - GHF332
For TE605105 stud.
* NOT required for 2.5Pi models.
Drive Shaft & Gear Assembly;
2000 Mk2/2000TC/2500S & 2500TC - (1) - 126786
Oil pump/Distributor.
2.5Pi Mk2 - (1) - 149099
Distributor/Metering unit.
Bush - Distributor Drive - (1) - 149776
Setscrew * - (1) - SH605071
Distributor to pedestal.
Washer - Locking - (1) - GHF331
Washer - Plain * - (1) - GHF300
* NOT required for 2.5i models.
Timing Cover - (1) - 217790
Oil Seal (timing cover) - (1) - UKC1110
Timing Cover Gasket - (1) - 211126
Setscrew;
Timing Cover to Block - (5) - SH605071
Timing Cover to Plate - (5) - SE605031
Washer - Locking - (10) - GHF332
Stud - Timing Cover - (2) - TE605105
Nut - (2) - GHF201
Washer - Locking - (2) - GHF332
Camshaft;
2000 Mk2 -
new - (1) - 307621
Reprofiled - (1) - 307621R
2.5Pi Mk2 -
New - (1) - 308778
Reprofiled - (1) - 308778R
2.5Pi Mk2 -
New - (1) - 311399
Reprofiled - (1) - 311399R
2500S & 2500TC -
New - (1) - 307621
Reprofiled - (1) - 307621R
Locating Plate - Camshaft - (1) - 105114
Setscrew - (1) - SH605071
Plate to block.
Washer - Locking - (1) - GHF332
For SH605071 setscrew.
Cam Follower (tappet) - (12) - 143552
Return to 2000/2500 Index Page 
Home About Rimmer Bros. Prices General Info Delivery How to Order Your Order Form News Restoration Projects Picture Library Triumph Links Free Catalogue Contact Us
The 'Triumph', 'Rover' and 'British Motor Heritage' Logos used herein are Registered Trade Marks of British Motor Heritage Ltd,
and are used with their Licence under the Special 'Heritage' approval Scheme.
All original part numbers & illustrations have been reproduced by kind permission of British Motor Heritage.