|
|
|
Triumph TR6 Starter Motor |
|
Page Contents
TR6 to commission no. CP53636/CC63895. TR6 from commission no. CP53637/CC63895
©Rimmer Bros Ltd - Registered in England No. 2155394. VAT No. GB 352 8473 40.
Starter Motor
Uprated Starter Motor
Consumables
TR6 PI cars were always fitted with a pre-engaged type Lucas starter motor of either the M418G or 2M100 model type. Due to further improvement by Lucas the later type 2M100 model starter is supplied for all replacement purposes. The M418G starter is identified by the Lucas part number 25626 stamped on the main casing. The 2M100 model is identified by the part number 25647 stamped on the main casing. M418G starter motors have the electrical carbon brushes bearing on the sides of the armature's commutator in a radial manner. The carbon brushes of the 2M100 bear against an end facing commutator in an axial manner. The components of the two design starters are not interchangeable, the complete starter motor assemblies are. If you intend to carry out repairs to your own starter motor you must establish which model starter is fitted by obtaining the information of model type and part number from the starter motor main casing. Without this information there is a good chance that the wrong spares are purchased to service your particular starter motor.
1. 
Starter Motor Assembly (factory, exchange) - (1) - GXE4439
Includes solenoid. All models.
Start Motor Assembly (reconditioned, exchange) - (1) - GXE4439R
Includes solenoid. All models.
These units are replacements for both types that were originally fitted. The original Lucas numbers and the models that they were fitted to are: Up to commission no. CP53636, Lucas model and part number M418G and 25626. From commission no. CP53637, Lucas model and part number 2M100 and 25647.
2. Starter Motor Assembly - (1) - 214914R
Reconditioned exchange. Lucas nos. 25626A/B.
3. Bracket (drive end) - (1) - 517466
4. Bush (drive end bracket) - (1) - 517467
5. Drive Pinion Assembly - (1) - 517462
6. Bush (drive pinion) - (1) - 517465
7. Ring (retaining bush) - (1) - 517463
8. Plate (operating lever) - (1) - 517464
9. Washer (thrust, drive end) - (1) - 517468
10. Drive Retention Kit - (1) - LU54245339
11. Collar (thrust) - (1) - 517469
12. Ring (spring, retaining drive) - (1) - 517470
13. Lever (pinion engaging) - (1) - 517461
14. Bolt (lever pivot) - (1) - 517459
15. Nut (locking pivot bolt) - (1) - 517460
16. Armature - (1) - 517473
17. Field Coil Set - (1) - 517475
18. Cover Band (brush gear) - (1) - 517454
19. Screw (cover securing) - (1) - 517455
20. Nut (cover securing) - (1) - 517456
21. Washer (thrust, fabric, commutator end) - (1) - 517472
22. Washer (thrust, commutator end) - (1) - 517471
23. End Plate (commutator) - (1) - 517457
Includes one pair of brushes and armature bush.
24. Brush Set (carbon, pair) - (1) - GSB103
25. Bush (commutator end plate) - (1) - 509818
26. Spring Set (brush tension) - (1) - 517458K
27. Spring (brush tension) - (4) - 517458
28. Bolt (through, fixing) - (2) - 511596
29. Solenoid Assembly - (1) - AEU1649
Attached by studs.
30. Sundry Parts Kit - (1) - 503721
31. Bolt (starter motor attachment) - (2) - HB915
32. Washer (shakeproof) - (2) - WE609
33. Washer (locking) - (2) - WL209
34. Nut (starter attachment bolt) - (2) - HN2009
35. Starter Motor Assembly - (1) - 218053R
Reconditioned exchange. Lucas no. 25647A/E/F/J.
Starter Motor Assembly - (1) - TKC3010R
Reconditioned exchange. Lucas no. 25714A.
36. Bracket (drive end) - (1) - 520458
Lucas no. 25647A/E/FJ.
Bracket (drive end) - (1) - LU54249562
Lucas no. 25714A.
37. Bush Set (drive end and commutator brackets) - (1) - 520465
38. Pinion Lever Engaging Kit - (1) - 520456
Includes pivot pin kit.
39. Pivot Pin Kit - (1) - 520455
40. Drive Pinion Assembly - (1) - 520457
Lucas no. 25647A/E/FJ.
Drive Pinion Assembly - (1) - LU54262658
Lucas no. 25714A.
41. Retention Kit (drive end) - (1) - 519558
42. Armature - (1) - 520460
43. Field Coil Set - (1) - 520461
44. End Plate (commutator) - (1) - 520454
Includes one pair of brushes and armature bush.
45. Brush Set (carbon, pair) - (1) - 520453
46. Sealing Kit - (1) - 520459
Includes solenoid end cap, bellows and brass cap and grommet for drive end bracket.
47. Bolt kit (through fixing) - (1) - 520464
48. Solenoid Assembly - (1) - 520462
Lucas no. 25647A/E/FJ.
Solenoid Assembly - (1) - LU76879
Lucas no. 25714A.
49. Sundry Parts Kit - (1) - 520466
50. Bolt (starter motor attachment) - (2) - HB915
51. Washer (shakeproof) - (2) - WE609
52. Washer (locking) - (2) - WL209
53. Nut (starter attachment bolt) - (2) - HN2009
These brand new starters are high torque, meaning their armatures will not suffer the same fate as the originals, especially on high compression engines. More reliable by design, they are half the weight of the original TR6 starter.. Bringing TRs (literally) into the millennium. No other parts are required and these are sold on an outright basis.
54. Starter Motor (uprated) - (1) - GXE4439UR
All models.
55. Shim (starter bendix position - (ar) - 102014
May be needed to obtain correct spacing.
56. Grease (copper, anti-seize, 85gm) - (ar) - RX1345
57. Lithium Grease (400gm) - (ar) - GGL111
Return to TR6 Electrical Index 
Return to TR6 Index Page
Home
About Rimmer Bros.
Prices
General Info
Delivery
How to Order
Your Order Form
News
Restoration Projects
Picture Library
Triumph Links
Free Catalogue
Contact Us
The 'Triumph', 'Rover' and 'British Motor Heritage' Logos used herein are Registered Trade Marks of British Motor Heritage Ltd,
and are used with their Licence under the Special 'Heritage' approval Scheme.
All original part numbers & illustrations have been reproduced by kind permission of British Motor Heritage.