|
|
|
Triumph TR6 Steering |
|
Page Contents
Escutcheons, Decals & Switches
To commission no. CP/CC50000 European models: From commission no. CP50001 to CR5000. European models: From commission no. CR5001. North American models: From commission no. CF12501. Waso Lowe and Fletcher Additional Items ©Rimmer Bros Ltd - Registered in England No. 2155394. VAT No. GB 352 8473 40.
Steering Rack
Steering Rack Mountings
Inner Steering Columns
Quick Racks
Consumables
Steering Wheels & Horn Pushes
Steering Column
Escutcheons, Decals & Switches
Steering Locks & Switch
Steering Lock Spares
Conversion Kit - LHD to RHD
1. 
Steering Rack Assembly (new) - (1) - 306829
RH steering.
Steering Rack Assembly - (1) - 306829R
RH steering. Reconditioned exchange.
Steering Rack Assembly (new) - (1) - 306830
LH steering.
Steering Rack Assembly - (1) - 306830R
LH steering. Reconditioned exchange.
2. Body (rack & pinion) - (1) - 305773
RH steering.
Body (rack & pinion) - (1) - 305774
LH steering.
3. Bush (rack tube, passenger side) - (1) - 128002
4. Cover (blanking, pinion housing) - (1) - 128020
5. Rack Bar - (1) - 208375
6. Plug (nylon, rack damping) - (1) - 145108
Held in place by passenger side rubber rack mounting bush.
7. Inner Tie Rod & Ball Pin Assembly - (2) - 142687
8. Housing (ball pin) - (2) - 128024
9. Pin & Ball - (2) - 139860
10. Socket (ball, ball pin to rack) - (2) - 120955
Alternative.
Socket (ball, ball pin to rack) - (2) - 158732
Alternative.
11. Shim (0.002", adjusting) - (ar) - 130031
Shim (0.004", adjusting) - (ar) - 153516
Shim (0.010", adjusting) - (ar) - 130032
12. Washer (tab, sleeve to housing) - (2) - 120957
13. Sleeve (adaptor) - (2) - 129963
14. Spring (ball pin to rack) - (2) - 120953
15. Nut (half, locking ball pin to rack) - (2) - 145364
16. Steering Rack Gaiter Kit - (1) - RTC2218-9
17. Gaiter (pinion end, driver's side) - (1) - RTC2219
18. Gaiter (passenger's side) - (1) - RTC2218
19. Clip (gaiter to ball pin shaft) - (2) - CS4009
20. Clip (gaiter to rack body) - (1) - CS4020
21. Wire (binding, gaiter to housing) - (1) - 512781
22. Track Rod End Assembly - (2) - GSJ156
23. Gaiter (grease, ball joint) - (2) - EAW2270
24. Clip (gaiter, OE track rod ends only) - (2) - 138869
25. Nut (nyloc, track rod to tie rod lever) - (2) - GHF224
26. Washer (plain) - (2) - WD600071
27. Nut (half, track rod end adjustment) - (2) - 128022
28. Bush (pinion, lower) - (1) - 127997
29. Washer (thrust, lower) - (1) - 128000
30. Pinion (RHD) - (1) - 134689
Pinion (LHD) - (1) - 134688
31. Washer (thrust, upper) - (1) - 127999
32. Bush (pinion, upper) - (1) - 127998
33. Shim (pinion, 0.005") - (ar) - 120941
Shim (pinion, 0.010") - (ar) - 130902
34. Plug (end, retaining 'O' ring seal) - (1) - 128001
35. 'O' ring - (1) - 128021
36. Pin (locating plug) - (1) - 128008
37. Circlip (retaining end plug in body) - (1) - 509537
38. Plunger (loading, rack to pinion) - (1) - 120946
39. Spring (loading plunger) - (1) - 126765
40. Shim (0.002", adjusting plunger) - (ar) - 120959
Shim (0.004", adjusting plunger) - (ar) - 120949
Shim (0.010", adjusting plunger) - (ar) - 132055
41. Cap (screwed) - (1) - 132053
42. Grease Plug - (1) - 133103
43. Grease Nipple - (1) - 56935
The grease nipple listed above should be fitted in place of the grease plug when lubricating the rack and pinion assembly.
44. Clamp Assembly (rack body to chassis) - (2) - 156024
45. Mounting Bush (rubber) - (2) - 139386
Mounting Bush (polyurethane) - (2) - 139386POLY
As an alternative to solid rack mounts polyurethane mounts offer increased strength and more responsive feel than original rubber.
46. Plate (reinforcing) - (2) - 133875
47. Washer (plain) - (4) - GHF301
48. Nut (nyloc) - (4) - GHF222
49. Solid Mounting Kit (uprated) - (1) - RR1370
A kit to replace the original rubber mountings and clamps. It consists of solid aluminium blocks clamping the rack body to the chassis frame by 'U' bolts. This system does eliminate rack float caused by oil soaked or worn rubber mounting bushes. The design of the solid mounting kit will transmit road noise, vibration and shocks up the steering column The standard rubber mounting system of course insulates the steering from such things.
Suitable for cars with original steering racks (not suitable for 'Quick Racks').
50. Cable Conductor (rack to 'U' bolt) - (1) - 134301
As fitted.
51. Steering Column Assembly Upper - (1) - 156060
Outer, non steering lock type. To commission no. CP/CC50000.
Steering Column Assembly Upper - (1) - 149869
Outer, steering lock type. To commission no. CP50000.
Steering Column Assembly Upper - (1) - 156060
Outer, RH steering. From commission no. CP52786.
Steering Column Assembly Upper - (1) - 154640
Outer, LH steering. From commission no. CP/CC50001.
52. Clip (turn signal cancelling) - (1) - 140549
53. Steering Column Upper (inner) - (1) - 149862
54. Clamp (steering column) - (1) - 122669
55. Plate (locating) - (1) - 125782
56. Screw (locating) - (1) - 125781
57. Nut (half) - (1) - JN2110
58. Bolt (clamp and plate to steering column) - (2) - BH604101
59. Washer (locking) - (2) - GHF331
60. Steering Column (lower) - (1) - 213308
61. Coupling (flexible) - (1) - 150696
62. Bolt (socket headed, coupling) - (2) - 150697
63. Adaptor (coupling to column)* - (1) - 150699
64. Bolt (adaptor clamping)* - (1) - 140349
65. Nut (self locking)* - (1) - GHF272
66. Washer (plain)* - (1) - WP21
* To commission no. CP75371/CC77477.
63. Adaptor (coupling to column)** - (1) - 156270
64. Bolt (adaptor clamping)** - (1) - HB813
65. Nut (self locking)** - (1) - GHF272
66. Washer (plain)** - (1) - WP21
** From commission no. CP75372/CC77478.
67. Cable Conductor (flexible coupling) - (1) - 130581
68. Wire (locking bolts) - (ar) - 30047
69. Universal Joint (column to rack) - (1) - 145377
70. Bolt (joint clamping) - (2) - GHF104
71. Nut (self locking) - (2) - GHF222
72. Washer (plain) - (2) - GHF301
The new Quick Rack has a high ratio pinion giving you lock-to-lock in only 2.5 turns, compared to the standard of 3.5 turns. Made for competition use, with stronger outer casing and a higher grade of steel rack for increased durability. Track rod ends not included.
This rack is designed to be used with special solid rack mounts, (included in fitting kit).
73. Quick Rack Assembly (RH steering) - (1) - 306829HR
Quick Rack Assembly (LH steering) - (1) - 306830HR
74. Fitting Kit - (1) - RR1421
75. Lithium Grease (400gm) - (ar) - GGL111
76. WD40 (400ml can) - (ar) - GAC111
77. Studloc (Loctite, 10ml) - (ar) - GAC100
78. Grease (copper, anti-seize, 85gm) - (ar) - RX1345
1. Steering Wheel - (1) - 308907
To commission no. CP/CC50000.
2. Centre Pad (horn push surround) - (1) - 518121
To commission no. CP/CC50000.
3. Steering Wheel and Centre Pad - (1) - 518535
From commission no. CP/CC50001 to CR/CF1.
4. Steering Wheel - (1) - 153937
From commission no. CP/CC50001 to CR/CF1.
5. Centre Pad (horn push surround) - (1) - 216508
From commission no. CP/CC50001 to CR/CF1.
6. Steering Wheel & Centre Pad - (1) - 160038
From commission no CR/CF1.
7. Steering Wheel - (1) - 313150
From commission no. CR/CF1.
8. Centre Pad (horn push surround) - (1) - 156170
From commission no. CR/CF1.
9. Nut (steering wheel attachment) - (1) - 105438
10. Washer (plain) - (1) - WP25
From commission no. CP/CC50001 or as fitted.
11. Mota Lita Steering Wheel (wood rim);
Includes boss and fittings.
13" diameter - (1) - RR117013
14" diameter - (1) - RR117014
12. Mota Lita Steering Wheel (leather rim);
Includes boss and fittings.
13" diameter - (1) - RR117313
14" diameter - (1) - RR117314
13. Mountney Steering Wheel - (1) - RL1466
Wood rim, semi-dished, 13"diameter. Includes boss and fittings.
15. Horn Push Assembly (Triumph medallion) - (1) - 150277
To commission no. CR/CF1.
16. Horn Push Assembly (Triumph word) - (1) - 159761
From commission no. CR/CF1.
17. Clip (3 pronged, horn push retaining) - (1) - 204741
To commission no CR/CF1.
18. Clip (barbed, horn push retaining) - (1) - 613766
From commission no CR/CF1.
19. Brush (horn contact, 2.6") - (1) - 142534
Brush (horn contact, 3.4") - (1) - 142534X
As fitted, check length.
Different length brushes are fitted according to different types of steering wheels. Please measure the brush length before ordering.
20. Steering Column Cowl Assembly - (1) - 611618
To commission no. CP/CC50000; models without steering locks.
Steering Column Cowl Assembly - (1) - 612072
To commission no. Cp/CC5000; models with steering locks.
Steering Column Cowl Assembly - (1) - 154731
From commission no. CP/CC50001.
Channel (mounting column switches) - (1) - 608136
21. Slip Ring, Cable & Insulator Assembly - (1) - 608462
22. Cable Assembly (slip ring) - (1) - 608356
23. Insulator - (1) - 608139
24. Bearing Assembly (steering column) - (2) - 209423
25. End Cap (aluminium) - (1) - 122718
26. Washer (bearing, nylon) - (1) - 122719
27. Grommet (rubber, steering column) - (1) - 610608
To commission no. CP/CC75000.
Seal (steering column) - (1) - 631205
From commission no. CP/CC75001 to CR/CF1.
28. Seal (foam, steering column) - (2) - 633679
From commission no. CR/CF1.
Retainer (seal, LH steering) - (1) - 631207
From commission no. CR1/CF1.
29. Retainer (seal, RH steering) - (1) - 631208
From commission no. CR1/CF1.
30. Cover (column harness) - (1) - 611369
31. Screw (clamping cover) - (1) - PT504
32. Washer (plain) - (1) - WP138
33. Washer (locking) - (1) - WL205
34. Nut (plain) - (1) - HN2005
35. Bracket (clamp, forward) - (1) - 608185
36. Strip (felt, forward bracket, long) - (1) - 608223
37. Strip (felt, forward bracket, short) - (1) - 608222
38. Rod (tie, between column brackets) - (1) - 611531
To commission no. CP/CC50000; models without steering locks.
Anti-Torque Strap (LH) - (1) - 147892
To commission no. CP/CC50000; models with steering locks.
Anti-Torque Strap (RH) - (1) - 147893
To commission no. CP/CC50000; models with steering locks.
39. Anti-Torque Strap (between brackets) - (1) - 154168
From commission no. CP/CC50001.
40. Screw (tie rod and clamp to bulkhead) - (2) - HU706
Models without steering locks.
Screw (tie rod and clamp to bulkhead) - (2) - HU710
Models with steering locks.
41. Washer (plain) - (2) - WP35
42. Washer (locking) - (2) - WL207
43. Nut (plain) - (2) - HN2007
44. Column Clamp (rearward, lower half) - (1) - 611529
45. Strip (felt, rearward bracket lower) - (1) - 608188
46. Column Clamp (rearward, upper half) - (1) - 611530
47. Spring (rearward clamp upper half) - (1) - 609639
48. Nut (plain, tie rod and bracket to dash) - (2) - HN2007
49. Nut (half, locking plain nut) - (2) - JN2107
50. Screw (clamping brackets) - (2) - HU808
Models without steering locks.
51. Washer (locking) - (2) - WL208
Models without steering locks.
52. Nut (plain) - (2) - HN2008
Models without steering locks.
50. Screw (brackets and anti-torque tie rod) - (2) - HU809
Models with steering locks.
51. Washer (plain) - (2) - WP8
Models with steering locks.
52. Nut (nyloc) - (2) - YN2908
Models with steering locks.
53. Cover (nut head) - (2) - 154172
Models with steering locks.
54. Tie Rod (upper) - (1) - 622137
Models without steering locks.
55. Screw (tie rod to rearward upper clamp) - (1) - HU706
Models without steering locks.
56. Washer (plain) - (1) - WP146
Models without steering locks.
57. Washer (locking) - (1) - WL207
Models without steering locks.
58. Nut (plain) - (1) - HN2007
Models without steering locks.
59. Screw (tie rod to bulkhead) - (1) - HU705
Models without steering locks.
The screw is also used to blank the captive nut in the bulkhead when the upper tie rod is not fitted.
60. Washer (locking) - (1) - WL207
Models without steering locks.
61. Washer (plain) - (1) - WP27
62. Escutcheon (light switch) - (1) - 708479
63. Escutcheon (indicator switch) - (1) - 708479
Without overdrive.
64. Escutcheon (indicator & overdrive switch) - (1) - 611974
Overdrive models.
65. Screw (escutcheon to cowl) - (2) - 510995
66. Nut (fix) - (2) - FC2803
67. Decal (indicator switch, RHD) - (1) - 611012
68. Decal (indicator switch, LHD) - (1) - 611011
69. Decal (lighting switch, RHD) - (1) - 611014
To commission no. CR1.
70. Decal (lighting switch, LHD) - (1) - 611013
To commission no. CR/CF1.
71. Decal (main/dip, headlamp and flasher switch, RH steering) - (1) - 621967
From commission no. CR1.
72. Decal (main/dip, headlamp and flasher switch, LH steering) - (1) - 621968
From commission no. CR/CF1.
73. Switch Assembly (lighting, RH steering) - (1) - 142579
To commission no. CR1.
Switch Assembly (lighting, LH steering) - (1) - 141858
To commission no. CR/CF1.
TR6 commission no. CP series cars are fitted with a floor mounted, foot operated headlamp dip/main beam change-over switch. All TR6s after commission no. CR1 had the headlamp dip on the lighting switch mounted on the steering column.
Switch Assembly (lighting, headlamp dip/main beam and flash, RH steering) - (1) - 152616
From commission no. CR1.
Switch Assembly (lighting, headlamp dip/main beam and flash, LH steering) - (1) - 152616
From commission no. CR/CF1.
74. Switch Assembly (indicator) - (1) - 147277
RH steering.
Switch Assembly (indicator) - (1) - 158966
LH steering.
75. Screw (switch attaching) - (4) - TP402
76. Washer (shakeproof) - (4) - WE604
77. Switch (overdrive, RH steering) - (1) - 147280
Switch (overdrive, LH steering) - (1) - 147281
78. Bezel (nut, overdrive switch) - (1) - 609792
79. Washer (shakeproof, internal) - (1) - WN715
80. Crash Pad (ignition switch) - (1) - 718813
From commission no. CP/CC50000.
81. Clip (fits Waso locks) - (1) - 627340
From commission no. CP/CC50000.
Clip (fits Wilmot Breeden locks) - (1) - UKC894
From commission no. CP/CC50000.
82. Washer (plain) - (1) - WP5
From commission no. CP/CC50000.
83. Washer (locking) - (1) - WL205
From commission no. CP/CC50000.
84. Nut - (1) - HN2005
From commission no. CP/CC50000.
The TR6 from CP50000 had a multitude of different steering lock types fitted for differing markets. Triumph had at least four different suppliers and over the life of your car the steering lock may well have been changed. For ease of identification you should order your ignition switch based on the presence or absence of a plastic loom connection plug. If you have a plug order part number UKC27191; if not order part no. 2190611. By rights the ignition steering lock switch assembly with the plastic loom connector plug should only be fitted to cars after commission nos. CR5001/CF12501....however....we fit what we can get to keep the car on the road.
For use wherever a steering lock is fitted.
85. Steering Lock & Ignition Switch - (1) - 132135
Neiman manufacture.
Attached with a circular clamp which meant you had to remove the steering column assembly to fit it!
North American models: From commission no. alternative CC50001 to CF12500.
86. Steering Lock & Ignition Switch - (1) - 2190611
Waso manufacture.
Steering Lock & Ignition Switch - (1) - 2190612
Lowe and Fletcher manufacture.
87. Switch (ignition, with Lucar connectors) - (1) - 579085
88. Steering Lock & Ignition Switch - (1) - UKC27191
Waso manufacture.
Steering Lock & Ignition Switch - (1) - UKC27192
89. Switch (ignition, with loom and plug) - (1) - 218959
88. Steering Lock & Ignition Switch - (1) - UKC27201
Waso manufacture.
Steering Lock & Ignition Switch - (1) - UKC27202
Alternative. Lower and Fletcher manufacture.
89. Switch (ignition, with loom and plug) - (1) - TKC1112
All models: From commission nos. CP/CC50001.
90. Screw (switch to lock) - (1) - FAS5
91. Shear Bolt (steering lock to column) - (2) - 152597
All models: From commission nos. CP/CC50001.
90. Screw (switch to lock) - (1) - FAS6
91. Shear Bolt (steering lock to column) - (2) - 152597
This is a 'bare essential' kit and it includes the major items required to do the job.... It does not include every single 'nut and bolt'!
Conversion Kit - (1) - RR1279
The above kit contains the following parts:-
Metal Dash Backing Assembly - (1) - 918203
Dash Crash Pad (lower, RH) - (1) - 818411
Dash Crash Pad (lower, LH) - (1) - 812081
Glovebox Compartment - (1) - 815746
Steering Rack (reconditioned) - (1) - 306829R
LHD unit required in exchange.
Brake Pedal - (1) - 148020
Clutch Pedal - (1) - 148021
Accelerator Pedal - (1) - 214420
Accelerator Cable - (1) - 160308
Speedometer Cable - (1) - GSD169
Rev Counter Cable - (1) - UKC2873
Clutch Pipe (master cylinder to slave cylinder - (1) - 308362
Wiper Arm (RH, silver) - (1) - 151886
Wiper Arm (LH, silver) - (1) - 151888
Below is a list of suggested parts you may also wish to consider purchasing in addition.
For full information, refer to appropriate section.
Dash Facia Veneer Panel. Available in teak or walnut finish. Refer to Interior Trim
Main Wiring Harness. Refer to Electrical Section.
Headlights (halogen conversion kit) - (1) - RB7129
Front Sidelight and Flasher Lamp (RH) - (1) - 215245
Front Sidelight and Flasher Lamp (LH) - (1) - 215246
Lighting Stalk (main beam). Refer to Electrical Section.
Indicator Stalk. Refer to Electrical Section.
Escutcheon Labels/Decals. Refer to Escutcheon, Decals & Switches
Clutch Master Cylinder. Refer to Clutch section.
Brake Pipe Kit. Refer to Brakes section.
Sun Visors (mirror/non-mirror). Refer to Interior Trim
Bracket (steering column strap) - (1) - 705219
Inner bulkhead - supports steering column.
The wiper motor will need to be reset as RHD and LHD versions park on opposite sides of the car. The conversion is simple. Remove the top cover plate on the motor and reuse the large gear. There is a peg inserted in this gear which determines the park position. Split the halves of the gear and rotate by 180° before reconnecting them and re-assembling into the motor. Check that the motor is correct for your TR; it should be stamped 115° to give the correct sweep. See also Electrical - Wiper System.
Return to TR6 Index Page 
Home About Rimmer Bros. Prices General Info Delivery How to Order Your Order Form News Restoration Projects Picture Library Triumph Links Free Catalogue Contact Us
The 'Triumph', 'Rover' and 'British Motor Heritage' Logos used herein are Registered Trade Marks of British Motor Heritage Ltd,
and are used with their Licence under the Special 'Heritage' approval Scheme.
All original part numbers & illustrations have been reproduced by kind permission of British Motor Heritage.