Triumph GT6 Column Mounted Switches - Mk1, Mk2 and Mk3

Order your Triumph GT6 Column Mounted Switches - Mk1, Mk2 and Mk3 ⛽ Low prices and fast, worldwide delivery ✈ British car experts ♚ Call ☎ 01522 568000 or ☎ 1-855-746-2767
Part No.: GRID008112

Prices displayed in:
For use wherever steering lock is fitted.
For added security the lock and switch was attached with a circular clamp which
meant one had to remove the steering column assembly to release it!!!!!
Qty Req-1, Model-GT6 Mk1 & Mk2, Item Info 2-factory option
Rate and Review this Product
132135
This part has been superseded
Use 2190612
Attached with a circular clamp which meant you had to remove the steering column assembly to fit it!
Qty Req-1, Model-GT6 Mk3 from KE/KF20000, Item Info 2-standard fit
Rate and Review this Product
2190611
In stock
£72.00 ex VAT£86.40 inc UK VAT
Quantity
With Lucar connections - 3 pairs and 1 single terminal

When used as a replacement for Stag MK1 (To LD20000 inc USA) Ignition Switch, to modify wiring, fit spade connectors to terminals 1, 2, 3 & 5 and transfer from original loom Brown wire to terminal 2, White & Pink to terminal 5, White to terminal 3 and White & Red to terminal 1. The remaining Red & Red/Green wires are for a sidelight functionality that prevents driving off with the sidelights only and can be insulated for safety and ignored.

This information is applicable to Stag MK1 (inc USA) only. Other models may require similar modifications if fitting this switch in place of one with the loom attached. Please refer to the appropriate workshop manual.
Qty Req-1, Model-GT6 Mk3
Rate and Review this Product
158459
In stock
£39.00 ex VAT£46.80 inc UK VAT
Quantity
2 position

TR6 comm no CP series cars are fitted with a floor mounted, foot operated headlamp dip/main beam change-over switch.
All TR6s after comm no CR1 had the headlamp dip on the lighting switch mounted on the steering column.

Wiring for this varies from the original wiring colours and is as follows:

- Brown Wire is power to Flash Feature
- Red Wire is power in to High / Low Beam
- Blue Wire is power out to Low Beam
- White Wire is power out to High Beam
Qty Req-1, Model-GT6 Mk2 & Mk3
5 out of 5 starsRead 1 Review(s)Rate and Review this Product
152616
In stock
£67.00 ex VAT£80.40 inc UK VAT
Quantity
Rate and Review this Product
158966P
In stock
£45.00 ex VAT£54.00 inc UK VAT
Savings:14%
£38.90 ex VAT£46.68 inc UK VAT
Quantity
Positive + : Wire Color Blue/ Red
Turn Left: Negative -: Wire color Green/Orange
Turn Right: Negative -: Wire color Green/White

New Line - Lucas Brand - The brand's famous green boxes have been a familiar feature of garages across the globe for decades. That’s because Lucas have always provided the parts that mechanics trust and keep close at hand to get the job done. It’s still true today. The Lucas portfolio covers premium quality products for automotive, motorcycle and home use.

Lucas products are driven by engineering excellence and a spirit of innovation that’s ensured our continued global success. The brand's reputation is built on an extensive range, exceptional technical durability and endurance, and outstanding quality.

Lucas has been providing all this for over 135 years - and we’re still growing. That’s why the brand has been continuously trading longer than any other automotive component brand in the world.
Qty Req-1
4 out of 5 starsRead 1 Review(s)Rate and Review this Product
158966PLUCAS
In stock
£47.00 ex VAT£56.40 inc UK VAT
Quantity
Rate and Review this Product
147280
Out of stock, expected soon. Add to cart and Back Order
£41.50 ex VAT£49.80 inc UK VAT
Quantity
5 out of 5 starsRead 1 Review(s)Rate and Review this Product
147281
In stock
£37.50 ex VAT£45.00 inc UK VAT
Quantity
Rate and Review this Product
708479
Out of stock, expected soon May 01, 2024. Add to cart and Back Order
£12.00 ex VAT£14.40 inc UK VAT
Quantity
3 position - side/main/dip

How to Apply

To apply correctly you will need the following: tape, tape measure, squeegee, or old credit card. (A spray bottle with Windex or mildly soapy water).
  1. Take measurements from your old decal to place it in the same/correct area.
  2. Clean the area, remove all wax and the old decal.
  3. Without removing the backing paper, position the decal where you want it and place a continuous piece of masking tape along the top edge of the decal to hold it in place. Double check to be sure it's lined up the way you want it.
  4. Lift up the decal (or one segment of the decal), being careful not to undo the tape at the top and starting from the top peel about half the backing paper away from the transfer paper and vinyl letter. Use the squeegee/credit card to lay it flat against the car working slowly and carefully from the top to the bottom removing the rest of the backing paper as you go. Use extra care as you lay the letter over any creases to be sure the decal doesn't gap over the crease.
  5. Once all the segments have been applied you can remove all the tape and transfer paper.
Optional, some customer like to have a little wiggle room and apply a very small amount of Windex or soapy water to the area. This can give you a second chance on moving the decal, but you will need to move quickly because this can soak the other transfer paper.
Qty Req-1, Model-GT6 Mk1
Rate and Review this Product
611400
In stock
£3.65 ex VAT£4.38 inc UK VAT
Quantity
2 position

How to Apply

To apply correctly you will need the following: tape, tape measure, squeegee, or old credit card. (A spray bottle with Windex or mildly soapy water).
  1. Take measurements from your old decal to place it in the same/correct area.
  2. Clean the area, remove all wax and the old decal.
  3. Without removing the backing paper, position the decal where you want it and place a continuous piece of masking tape along the top edge of the decal to hold it in place. Double check to be sure it's lined up the way you want it.
  4. Lift up the decal (or one segment of the decal), being careful not to undo the tape at the top and starting from the top peel about half the backing paper away from the transfer paper and vinyl letter. Use the squeegee/credit card to lay it flat against the car working slowly and carefully from the top to the bottom removing the rest of the backing paper as you go. Use extra care as you lay the letter over any creases to be sure the decal doesn't gap over the crease.
  5. Once all the segments have been applied you can remove all the tape and transfer paper.
Optional, some customer like to have a little wiggle room and apply a very small amount of Windex or soapy water to the area. This can give you a second chance on moving the decal, but you will need to move quickly because this can soak the other transfer paper.
Qty Req-1, Model-GT6 Mk2 & Mk3
Rate and Review this Product
621968
In stock
£3.60 ex VAT£4.32 inc UK VAT
Quantity
How to Apply

To apply correctly you will need the following: tape, tape measure, squeegee, or old credit card. (A spray bottle with Windex or mildly soapy water).
  1. Take measurements from your old decal to place it in the same/correct area.
  2. Clean the area, remove all wax and the old decal.
  3. Without removing the backing paper, position the decal where you want it and place a continuous piece of masking tape along the top edge of the decal to hold it in place. Double check to be sure it's lined up the way you want it.
  4. Lift up the decal (or one segment of the decal), being careful not to undo the tape at the top and starting from the top peel about half the backing paper away from the transfer paper and vinyl letter. Use the squeegee/credit card to lay it flat against the car working slowly and carefully from the top to the bottom removing the rest of the backing paper as you go. Use extra care as you lay the letter over any creases to be sure the decal doesn't gap over the crease.
  5. Once all the segments have been applied you can remove all the tape and transfer paper.
Optional, some customer like to have a little wiggle room and apply a very small amount of Windex or soapy water to the area. This can give you a second chance on moving the decal, but you will need to move quickly because this can soak the other transfer paper.
Qty Req-1, Model-GT6 All Models, Item Info 2-column fitting
4 out of 5 starsRead 1 Review(s)Rate and Review this Product
611012
In stock
£2.75 ex VAT£3.30 inc UK VAT
Quantity
Different length brushes are fitted according to different types of steering wheels. This one is the standard length as fitted to original spec. steering wheels. If a non original steering wheel has been fitted a longer horn brush may be required.

Please measure the brush length before ordering. If a longer horn brush is required; please order part number 142534X.
Qty Req-1, Item Info 2-horn push
Rate and Review this Product
142534
In stock
£9.95 ex VAT£11.94 inc UK VAT
Quantity
Different length brushes are fitted according to different types of steering wheels. This one is longer than that fitted to original spec. steering wheels and may be required if a non original steering wheel has been fitted.

Please measure the length of the brush fitted to your vehicle to ensure you are ordering the correct part. If the standard brush is required; please order part number 142534.
Qty Req-1, Item Info 2-horn push
Rate and Review this Product
142534X
Out of stock, expected soon. Add to cart and Back Order
£18.30 ex VAT£21.96 inc UK VAT
Quantity
12 month warranty
Worldwide shipping
Price Match
Customer Comments
"They are always helpful with enquiries and answer questions very quickly." Customer Comment
Product Description

Triumph GT6 Column Mounted Switches - Mk1, Mk2 and Mk3

Review: Matthew Goninon Submitted: 03/07/2020

Overall5 out of 5 stars.
verified

Subject
excellant.

Did this item work well with your project? What vehicle type are you using this for?
purchased for future retoration of 1968 13/60 estate.